Revolving branch

Introduction

Revolving branch are those branch which are used for extinguishing fire which occur in that place where firefighter can reach is very difficult. then we can use this branch by making hole on terrace. mostly these type of branch are used in navy. 

material and about it

Revolving branch are used at 150 psi maximum operating pressure  and is made up of 63 mm male instantaneous coupling that use to connect on hose and have 9 holes of 6.35 mm diameter and these holes are in dome shape on a cylindrical cap that are supported on ball bearing so that it can revolve at around 360 degree. Each hole has a length of 3.12 cm ,three on the circumference of the plane of revolution but inclined 600 to the tangent of the circular revolving plane, three in the center of the upper half pointing upwards at 600 to the vertical.

Construction

These revolving branch are made up with help of sand casting, die casting of grade 3 of IS 292, Hot forging of Grade 1 of IS 291, Gravity die casting of IS 1264.

Test 

the branch should rotate for about 10 hours without any leakage or failure at pressure of 1 MN/m square.
All these test and manufacturing are done according to IS 906.

Comments

  1. Aluminium Die CastingAugust 27, 2020 at 10:22 PM

    I agree with a lot of the points you made in this article. If you are looking for the Aluminium Die Casting, then visit Aluminium Die Casting. I appreciate the work you have put into this and hope you continue writing on this subject.

    ReplyDelete

Post a Comment

i request please do click on the blog heading to see which blog you want to see and please leave a comment on that blog

Popular posts from this blog

Fire

A fire is a exothermic chemical process in which fuel gets ignited in presence of oxygen and gave out heat and light. A fire is an exothermic reaction because it gives out heat and light in the surrounding. It occurs in 4 stages that are Incipient, Smouldering, Growth and at last it gets decay. In first stage that is incipient in this stage when heat, oxygen and fuel combines and evolve in chemical reaction in this stage a person can't able to see the heat and smoke then after incipient stage. Smouldering Stage occurs in this stage a person or a fire fighter can only see the smoke as the fuel burn slowly and only smoke can be visible and no flame will be seen. Smoke generated from fire has many toxic gases such as carbon monoxide, aldehydes, acid gases, sulfur dioxide, nitrogen oxides and many more, Due to release of these toxic gases from smoke generated by fire people loss their life more in comparison to fire. Due to generation of carbon monoxide from smoke it get dissolved in
Read more

History and types of sprinkler

In 1812 the first sprinkler system was installed in United kingdom at Theater royal, Drury lane. At that time these systems were Designed in such that the cylindrical airtight reservoir contains 95,000 litres which was fed by 250mm water main which supplies water to all parts of theater. Types of Sprinkler   1. Perforated type sprinkler system-  This type of system were used in textile mills in new England as a fire protection but the difficulty was that they were not automatic these sprinkler system were used in 1852 to 1885.After that  Philip W. Pratt of Abington, Massachusetts  started experimenting for automatic sprinkler in around 1860 after that in 1872 he patented this system. 2. Automatic sprinkler System- Henry S. Parmalee of New Haven, Connecticut, is considered the inventor of the first practical automatic sprinkler head .After that parmalee improved the system which was patented by Philip W.  Pratt. In 1874 the piano factory which was owned by Henry S. Parmalee installed it
Read more

Summary of IS 942 Portable fire pump set

 This pump set shall be of 275 litre/ min and have a pressure of 4 kgf/cm square. and fitted on a steel frame with anti-vibration coil.  Design The design of the engine used in pump should be of single cylinder two stroke or four stroke. The engine can either be driven of diesel or petrol. and should be air cooled. Pump The pump that will be installed should be single stage centrifugal pump and the casing of the pump shall be designed in such a way that there is easy excess to impeller and can easily inspect and erect the pump. the pump shall be fitted with mechanical gland of  self adjusting type.  test of pump performance is done at 27 degree Celsius at 760 mm of mercury. The pump shall be tested with suction strainer fitted continuously for 4 hours shall be with a lift of 3 m for the following duties: output Pressure I/min          kgf/cm 2 545                  2.5 365                  3.5 275                  4.0 The primer of the pump shall lift the water from at least 7 m of heig
Read more